- The short arm of an Allen wrench (typically a 3/16 size, which is provided with the bow) should be inserted into the bolt to ensure that it is correctly slotted. Then, using the wrench, tighten or loosen the bolt by turning it in either a clockwise or counterclockwise direction. To get the desired weight in each arm of the bow, adjust the tension of each arm.
How do you adjust the draw length on a diamond carbon cure?
Diamond bows include a universal draw length adjustment feature that does not require the use of draw length specific modules. This functionality is made feasible thanks to the Rotating Mod System. Your draw length may be modified by simply rotating the module clockwise or counterclockwise. Typically, 1/2 inch increments are used to alter the draw length.
Is Diamond Archery a good bow?
Diamonds are really attractive bows that are simple to shoot. They were previously known as the single cam series for Bowtech. Single-camera setups are often less difficult to film and a little more forgiving than multicam setups. They are comparable to Matthew’s solo cameras and are of far higher quality than the mission footage from the missions I’ve filmed.
How do you measure your draw length for a bow?
Place your back against a wall and stretch both of your arms out against the wall to determine the length of your draw length. Simply measure the distance between the ends of your middle fingers on both arms, hands, and chest. This is the length of both arms, hands, and chest. Your draw length is calculated by subtracting 15 from this measurement and dividing the result by two.
How far can you back out limb bolts?
What is the maximum distance I can back my limb bolts out and how many pounds of draw weight do I lose with each turn? The maximum number of spins that you can make with your limb bolts on most Hoyt bows is eight on most models (8).
Is Diamond A carbon?
Diamond is made up of only one element, carbon, and it is the arrangement of the carbon atoms in the crystal lattice that gives diamond its extraordinary characteristics. Compare the crystal structures of diamond and graphite, which are both made up entirely of carbon.
How do you adjust the draw weight on a bow?
It is necessary to unload or load extra stress (flex) on the limbs in order to alter the draw weight. This is accomplished by tightening or loosening the limb bolts, respectively. If you want to raise the draw weight to its maximum poundage, tighten the limb bolts (in the clockwise direction) until all limbs are snug against the riser.
How do you adjust the draw weight on a bowtech guardian?
The replacement of string and cables, as well as the adjustment of the draw weight, on the Guardian and Commander Center Pivot Bows does not necessitate the use of a bow press. To modify the draw weight, back off both limb bolts in the same amount of time counter-clockwise (1 complete turn Equals about 1 pound).
How do you change the draw weight on a Barnett Vortex youth bow?
The draw weight on the Vortex may be adjusted from 16 to 45 lbs depending on the combination of the module used and the position of the string (positive, neutral, negative). In order to change the draw length modules, no bow press is required; however, in order to change the string position (+ or –) on the cams, a bow press is required as well.
How fast does a diamond bow shoot?
The Diamond Infinite Edge has an FPS of 310, which is quite good for a compound bow aimed for beginners to intermediate shooters. There are quicker bows on the market—some of the most expensive versions can shoot at speeds of up to 370 FPS, if you can believe it—but you’ll only find bows with that kind of FPS on the most expensive models.
Where are diamond bows made?
Diamond bows are handcrafted in the United States by dedicated individuals who take delight in every step of the manufacturing process. From our in-house string facility to our high-quality finishing process, we have you covered. All of this is being done to create the most technologically sophisticated archery product known to man, while maintaining the high level of quality and service you would expect.
Who owns Diamond Archery?
When bow hunter Ryan Barkdull decided to
construct an archery range to a facility he purchased for his Midwest Turf & Construction business six years ago, he was merely searching for a place to practice his craft.